Server not accessable from WAN/WAN address

[wepspec]

Hello

I've read the forums for about 5 hours looking for my solution.
I understand most of the solutions but they dont seem to fix my problem.

I can't connect to the TS2 server unless I use the LAN address of my pc.
my freinds can't connect at all.
I couldn't connect to their servers ( they were running an older version beta-I think)
I know this... they did not have the option of getting the web server list in their client )
They upgraded their clients and still cant connect to me.
My server appears in the web server list but when I try to connect it says:
No reply from server, maybe the server is offline or maybe TS is not running on it.

I have tried bypassing my router ( connected the RJ45 cable to DSL modem, rebooted, verified web access)-still no connect, so not a router prob.
I have completely uninstalled Zone Alarm and cleaned the registry of all traces of it.
I can administer the server.
I can connect to other servers in the web server list.
Ghost Recon worked perfectly on ubi with no router/modem modifications.

Below you will find specs on my system and more things I have done to get TS2 to work.
I can ping the server's external address, just pinging the modem.

Appears to me now (9-3-02) to be related to the NAT in my modem. I can setup static NAT table in the modem, but it will not accept settings for static routing.

It might also help to know that neither Roger Wilco or the Voice over Net from MSN will function.

Software:
--------------------------------------------------
Win98SE ver 4.10.2222A

TS2 Server - I cant find ver. # but I downloaded from teamspeak.org 8-30-02
TS2 Client 2.0.13.13

PC:
--------------------------------------------------
BMO-BuiltMyOwn
VIA Motherboard
Chipset AMD 756
AMD 900Mhz T-bird
196MB RAM
NIC- Macronix MX987xx (http://www.macronix.com/web/P_multim...a?OpenDocument)

Network config
Client for Microsoft Networks
Macronix MX987xx Family Fast Ethernet Adapter (ACPI)
IPX/SPX Protocol
NetBEUI
TCP/IP
share level access
file and print sharing disabled

Network:
--------------------------------------------------
Modem:
Adsl Megabit Modem 500L ( for specs. http://www.techconcepts.com/p_500l.html )
BSP Version: 2.2
Software Version 2.8.5
Protocol G.hs
System Mode PPP over ATM

WAN
IP address 207.191.54.121 (set to dynamic by ISP but doesn't change - ever)
netmask ( subnet ) 255.255.255.0

LAN
IP address 192.168.0.1
Subnet 255.255.255.0
DHCP enabled

Lease IP Address Range 192.168.0.2 - 192.168.0.65 ( not changeable )
I can setup 32 static NAT entries - but don't what to set them to
Table looks like this....

Private Proxy Remote
IP Port IP Port IP Port Protocol
0.0.0.0 0 0.0.0.0 0 0.0.0.0 0 UDP-orTCP

I can setup 32 static routes - but don't what to set them to
Setup looks like this....
Destination 0.0.0.0 netmask 0.0.0.0 gateway 0.0.0.0
--------------------------------------------------
Router: D Link DI-704
Firmware version 2.57 build 3
ftp://ftp2.dlink.com/Gateway/di704/P...-datasheet.pdf

WAN
IP address 192.168.0.2 (static)
Subnet 255.255.255.0
Gateway 192.168.0.1
DNS servers 207.191.12.10, 207.191.12.20

LAN
IP address 15.150.0.10 I've tried several others ( 10.10.100.1 , 192.167.0.1 , 12.110.0.1 )
DHCP enabled
IP pool starting address 11
IP pool ending address 20 ( I've changed these values as I changed LAN IP addresses )

Can block access to Internet by MAC address
( disabled )

Virtual server settings
Service Ports Server IP
8766-8767 15.150.0.6 ( my PC )
51234 15.150.0.6

Special Application Settings I've tried many combinations
Trigger Incoming Ports
51234 8766-8767
8766 8766-8767
8767 8766-8767

Packet Filtering - I disabled inbound and outbound for TS2

I even set my PC as the dreaded DMZ host (currently disabled)


In my haste to provide all information that might be needed, I neglected to ask for help.....

Please, if someone has any idea what to do/try, your assistance would be greatly appreciated.

[FuZe]

Geeeah!

You've tried everything I would have tried. I'm baffled.

Try this though. Set your servers port to 69 (common TFTP port) in your server.ini file and restart the server. Try to connect using that port. Just an idea.

[wepspec]

Well, I tried it, sorry - no luck. I appreciate the suggestion though.